TCCoA Forums banner
1 - 13 of 13 Posts

· Registered
1995 40th Anniversary Edition 4.6L
Joined
·
73 Posts
Discussion Starter · #1 ·
Couple of huge hurtles but able to make some good progress recently.
Finished cutting/boxing/welding K-member (since no aftermarket when started) and installed engine with homemade engine mounts. Lowered steering rack with off set bushings and got engine to fit where the 4.6 sat.
Headers are from Ultimate Headers (S550 Mustang), and they helped move a couple tubes to fit the TBird perfectly.
The pics of engine in are deceiving, it does not stick up that hi, however, the TBird front clip is real thin going forward, and the engine is high above fenders. Looking at new hood to fit.






I have the Griffin 3 core radiator in and intercooler also in. The radiator I moved one inch forward (into radiator support), so I could make room for reverse facing alternator and aftermarket fan. Coyote front timing cover is bigger and takes up more space forward. Also have the trans cooler/fan installed, just need to do plumbing for trans cooler and intercooler.






Also finished the fuel supply, had to get to a bigger fuel pump, 455lph vice 255lph. The new pump has a bigger bottom than stock pump so I cut bottom of hat, return tube, and welded a new mount for new pump. I used factory hard lines, press/return but replaced press line for a 3/8 line. All lines, filter/check valve/regulator all installed and done.


Moved on to the rearend so I could finish the bigger items and order the new drive shaft.
I did some powder coating on diff and LCA's, and rebuilt/renewed everything.
3.73 gear with the Tac-Loc and axles from Drive Shaft Shop (ordering drive shaft from here also). DSS has been real good to work with, and they list axles specific for our TBirds. I got the 31 spline axle set. Also made a new ID tag for rearend, copy with my initials and date done...lol little fun.

 

· Registered
1995 40th Anniversary Edition 4.6L
Joined
·
73 Posts
Discussion Starter · #4 ·
After Christmas will order drive shaft, finish rear and brakes, front spindles/brakes, then down for plumbing and electrical, plenty electrical.
 

· Registered
1995 40th Anniversary Edition 4.6L
Joined
·
73 Posts
Discussion Starter · #10 ·
That’s fantastic news! A lot of guy on here are worried about modding the tunnel to fit. Seems like it’s a Str8 coward swap to me. Thanks!
I think it will be straight forward also. The length from engine mount plates to the bell housing is same on 4.6 and coyote. I'm sure I have the engine in same place as 4.6 on this one and it fits well. I used a 6R80 trans mount adapter from Summit, and it aligns with factory cross member.
 

· Registered
1995 40th Anniversary Edition 4.6L
Joined
·
73 Posts
Discussion Starter · #17 ·
Do you have any pictures from the cross member?? Where did you cut and how did you box it back in.
I'm very interested in that

Thx
The cross member just needed a little more angle on sides, then straight down in front. Then box it up.
I should have grinded my welds, but they are strong LOL. It took a while for all trial fits, measuring, cutting, repeat....etc.




 

· Registered
1995 40th Anniversary Edition 4.6L
Joined
·
73 Posts
Discussion Starter · #20 ·
On to mounting brackets for some accessories. These are power steering reservoir and Whipple coolant reservoir.
Takes up a lot of time to think of, build and paint. These two are mounted to PDB and shock tower. Still have to figure out radiator reservoir, PCM, and air filter.....


 

· Registered
1995 40th Anniversary Edition 4.6L
Joined
·
73 Posts
Discussion Starter · #22 ·
Wow man that's an excellent job you are doing. The engine is gorgeous and the car looks super clean too. Which transmission are you using?

What a great swap/mod, that thing will rock set up that way.

I did not read all your input so I missed the power level you are at. It looks pretty stock in the photos, but hard saying. I would think stock with the VVT in that thing you won't need much more to get 500 to the wheels right?
Thanks, I'm using the 6R80auto that came with engine from the Mustang.
As for the power, I'm using the Whipple Gen5 supercharger. The person advising me on set up and who will do the Tuning is Jim from JDM Engineering (He has done all my tuning in past years), he advised for Stage1, throttle body and size of injectors, and assures me of 700-725 horsepower. I do not believe that's to the wheel, but truly feel its plenty for a street cruiser.
We do not have a track here right now, but will surely find some WOT time, lol.
 

· Registered
1995 40th Anniversary Edition 4.6L
Joined
·
73 Posts
Discussion Starter · #24 ·
Still a long way to go but making some good progress lately.....
Suspension, brakes done and installed. Plumbing for trans cooling, power steering and supercharger cooling all done. Driveshaft installed, gas tank, fuel pump and system all done.
Today's milestone is the wheels are back on and car is down on its own weight.
Now the Control Pack install and all the electrical to merge with the car starts...another big job but oh well.... it's what we like to do, LOL






 
1 - 13 of 13 Posts
Top